• 281-282-9200
  • This email address is being protected from spambots. You need JavaScript enabled to view it.

Slag Grinder – Engineering & Design

Crushers and Slag grinders are often applied in Materials Handling and Gasification plants to reduce the size of quenched slag from the gasifier’s tap-hole or break clinkers from slow moving bed reactors. These clinkers are typically brittle and relatively easy to crush, but may be larger and very hard and abrasive when sintered during a reactor transient or upset conditions. Also, these crushers are often of toothed roller type, integrated in a pressure vessel subject to charge / discharge cycles, slow rotating yet transmitting very high torques and crushing forces. This makes it simultaneously a ‘machine’ and a ‘pressure vessel’.

PROBLEM: A slag breaker dating from the 1970’s required replacement. The new design had to incorporate lessons learned in operations and maintenance, fit accurately into the existing structure and inlet-outlet flange face-to-face envelope, and re-use the existing drivetrain. The crusher must reduce slag as well as occasional refractory tiles or bricks, dislodged from the gasifier hot face, to no more than 1” in size to avoid bridging and arching in the outlet. The equipment must be designed, manufactured, tested and delivered to site under schedule constraints, in time for the next scheduled shutdown.

SOLUTION: KnightHawk engineering digitized hand drawn blue-prints and developed 3D CAD models (below) applied in concept development, client reviews and manufacturer reviews and design. Detailed 2D CAD drawings and part lists as well as geometry and meshing for Finite Element (FEA) designs, were developed from this model. The pressure vessel was designed as per ASME VIII Division 1 with supplementory analysis by FEA as per ASME/API 579-1 Fitness for Service (FFS) by using the methods and guidelines from ASME VIII Division 2 Part 5. The rotating parts and breaker element were integrated into the pressure vessel by shaft, breaker tooth, breaker plates, gland seals, end bearings and a bolt-on cantilever drive unit (not shown) consisting of a motor, gearbox and coupling. The breaker element is protected from overpower, including an auto reverse, circuit breaker, shear pin and hydraulic coupling.

The breaker element and teeth must be accurately sized and designed for particle size reduction, throughput and slag crush strength requirements, to ensure effective crushing yet avoid jammed rotor and lockup conditions. KHE determined the required grinding energy by the 3rd comminution theory as per Bond’s equation using a ‘Work Index’ to define motor horsepower, torque and crushing power requirements as per its experience for this type of equipment.

The pressure vessel design must include for considerations of (i) internal pressure-temperature design (ii) fatique loading from batched feed and pressure cycles (iii) bending and crushing forces from drivetrain weight and work (iv) thermal loading from batch cycles and (v) modal analysis to ensure no coupling between any fundamental natural frequency, fN, and any of the forcing functions or excitations from the rotating parts result in resonant vibrations.

Materials selection, stainless steel and tungsten carbide weld overlay of internal surfaces subject to corrosion, impact, crushing and flow-erosion, must be carefully selected to provide a robust yet manufacturable and cost effective equipment fit for service over its design life.

The seal design must include for effective sealing against varying pressure-temperature conditions, a seal flush to ensure cooling, lubrication and avoid intrusion of abrasive particles. The seal design is schematically shown right. This seal design is typically a multi packing ring compressible gland type with lantern ring assembly. The seal acts in the annular space between the shaft nozzle housing (2) and the rotating shaft (6). The nozzle bore is weld over-layed (3) in Stainless Steel and final machined to diameter and surface finish presenting the outer seal surface. A shaft sleeve (7) is located by a key (13), retaining washer (8) and threaded lock nut (9). This shaft sleeve is located by the breaker teeth hub (5). An inner compression ring (4) is bolted (16) to the housing. Sealing between the shaft sleeve and the shaft, preventing slurry intrusion and leakage is provided for by two O-rings (11).
Succesfull design was achieved by :

  • A multi-party, collaborative design process including original OEM Designer, Owner-Operator, KHE Specialty Engineering and Manufacturers all with significant experience in industry.
  • A multi-disciplinary approach including process, mechanical, metallurgical and controls.
  • A multi-physics approach including code ‘design by rules’, FEA ‘design by analysis’, 1st principle machine and structural design by correlations as well as fatique, thermal and modal analysis
…ensuring a design fit for purposes and with adequate protection against failure.

Specialists in Design, Failure Analysis and Troubleshooting of Static and Rotating Equipment


  • Failure Investigation
  • Field Service
  • Rotordynamics
  • Rotating Equipment Analysis
  • Vibration Analysis
  • Computational Fluid Dynamics (CFD)
  • Finite Element Analysis (FEA)
  • Acoustic Analysis
  • Stress Analysis
  • Metallurgical and Metrology Lab
  • Fit for Service Analysis
  • Expert Witness